by 
(1) The resultant force of force application shall pass through the axis of IKO bearing as far as possible, which requires that the force Disassembly Of Iko Bearing application point shall be uniform, symmetrical and stable, and the force shall be applied through the spherical surface or parallel to the axis.
(2) The force should be applied stably and evenly without impact, which requires the use of oil pressure or Disassembly Of Iko Bearing tools that can apply stable tension or pressure. When hammering has to be used, it should also be buffered by soft metal such as copper sleeve without chip falling, and the knocking force should be as light as possible. Hammer with a copper rod or hammer.
(3) Avoid applying force through the rolling element, which requires applying force through the inner ring when installing and removing the Disassembly Of Iko Bearing inner ring (shaft ring) and through the outer ring when installing and removing the outer ring.
(4) The drag force shall be maintained to a proper extent. For example, when installing IKO bearing, stop the force when IKO bearing is just installed in the correct position, and ensure that the end face of ferrule (washer) is Disassembly Of Iko Bearing against the seat hole or the shoulder end face of shaft, which can not be squeezed too tightly or installed in place.
Unlike cylindrical bore bearings, the interference of tapered bore bearings is not determined by the selected shaft fit tolerance, but by the advancing distance of the bearing on the tapered journal, shaft sleeve or withdrawal sleeve. The radial internal clearance of the bearing decreases with the advance of the bearing on the conical journal. By measuring the reduction value, the degree of interference and the tightness of the fit can be determined.
When installing self-aligning ball bearings, carb ring roller bearings, spherical roller Timken bearings and high-precision cylindrical roller bearings with conical holes, the Disassembly Of Iko Bearing reduction value of radial internal clearance or the axial propulsion distance on the conical base shall be determined as the measure of interference. See the relevant product section for the guidance values of clearance reduction and axial propulsion distance.
Small bearings can be pushed to a conical base using nuts. In the case of shaft sleeves, sleeve nuts are used. Disassembly Of Iko Bearing The small disassembly sleeve can be pushed into the bearing hole with a nut. The nut can be tightened with hook wrench or pneumatic wrench. Before installation, add a little oil to the surface of journal and sleeve.
The installation force required forlarge Timken bearings is significantly increased and hydraulic nuts and / or oiling methods shall be used.The Disassembly Of Iko Bearing above two methods can significantly simplify the installation process. The oil filling equipment required to Disassembly Of Iko Bearing operate the hydraulic nut and use the oil filling method is supplied. For details of these products, see the relevant section in the online catalog “maintenance and lubrication products”.
When the hydraulic nut is used to install the bearing, it must be positioned on the threaded part of the journal or the thread of the sleeve, so that the annular piston is close to the inner ring of the bearing, the nut on the shaft or the retaining ring installed at the shaft end. Press the oil Disassembly Of Iko Bearing pressure into the hydraulic nut through the oil pump to move the piston axially with the force required for accurate installation. Use the hydraulic nut to install the spherical roller bearing onto the
Using the oil injection method, the oil is injected between Timken bearing and journal under high pressure to form an oil film. This oil film separates the mating surfaces and significantly reduces the friction between the mating surfaces. This method is generally used when installing the bearing directly on the conical journal, but it is also used to install the bearing on the set sleeve and push sleeve specially prepared for the oil injection method.
The oil pump or oiler generates the necessary pressure to inject oil between the mating surfaces through the groove and oil distribution channel on the shaft or sleeve. When designing the bearing layout, the necessary grooves and channels on the shaft must be considered. The Disassembly Of Iko Bearing spherical roller bearing is installed on the withdrawal sleeve with oil groove. The withdrawal sleeve is pressed into the bearing hole by injecting oil into the mating surface and tightening the screws in turn.