In most cases, the outer ring of this bearing has a lock, so it is unable to seal the resulting annular groove, so that many angular contact ball bearings used on the machine tool spindle cannot be greased like other bearings used on other host machines. If a set of auxiliary lubrication system is installed, it will not only increase the cost, but also make the structure of the machine tool more complex.
The advanced method is to insert a new type of sealing ring with groove into the bearing. The depth of the groove is slightly shallower than Angular Contact Ball Bearings that of the standard bearing, and it is just suitable for the intersecting part to fill the gap left by the outer ring flange. Adding this sealing ring can not only prevent the leakage of grease from both sides of the bearing, but also prevent the invasion of dirt from both sides of the bearing.
which is used for infinite stroke and cylindrical shaft. Because the bearing ball is in point contact with the shaft, the service load is small. Angular Contact Ball Bearings The steel ball rotates with minimal friction resistance, so as to obtain high-precision and stable motion. Linear bearings are widely used in precision equipment such as electronic equipment, tensile testing machines and digital three-dimensional coordinate measuring equipment, as well as sliding parts of industrial machinery such as multi axis machine tools, punches, tool grinders, automatic gas cutting machines, printers, card sorting machines, food packaging machines and so on.
grease Inject anti-corrosion oil into the linear bearing.Angular Contact Ball Bearings If grease is used for lubrication, remove the anti-corrosion oil with kerosene or organic solvent, and add grease after air drying. It is recommended to use adhesive mark N0 2 lithium soap grease Oil lubrication If the anti-corrosion oil does not need to be removed when lubricating with oil, the lubricating oil with ISO viscosity grade vg15-100 can be selected according to the temperature change Shaft lubrication can be supplied from the oil supply pipe or from the oil hole on the outer bearing seat.
oil lubrication is not suitable for bearings with sealing rings without holes. Linear guide bearing: Angular Contact Ball Bearings A groove or ridge made of metal or other material. A device that can bear, fix, move a device or equipment and reduce its friction. A longitudinal groove or ridge on the surface of a guide rail for guiding and fixing machine parts, special equipment, instruments, etc. Guide rail is also widely used in our daily life, such as the sliding slot of sliding door, train track and so on.
namely radial thrust ball bearing, can be loaded with more steel balls, its radial bearing capacity is greater than that of ordinary ball bearing, and can also bear large axial load or pure axial load at the same time. Angular Contact Ball Bearings Its allowable working speed is similar to that of deep groove ball bearing and its support rigidity is stronger, but it requires accurate installation and is very sensitive to axis misalignment error,
Generally, it does not need to bear the radial load alone, but it must bring additional axial load while bearing the radial load. This kind of bearing has many variants and is widely used. It is often made into three series with 15 °, 25 ° Angular Contact Ball Bearings and 40 ° contact angles. The larger the contact angle is, the higher its axial load capacity is. However, it is appropriate to use a small contact angle at high speed.
Most of these bearings are used in pairs for small-span rigid double support shafts or precision spindles. When in use, the clearance should be carefully adjusted. By changing the axial distance between the inner and outer rings of the bearing, Angular Contact Ball Bearings the internal clearance of the bearing can be adjusted. At the same time, several sets of bearings can be installed in parallel and given a certain pre interference, which can improve the rigidity of the bearing system.
can only bear the axial load in one direction. At the same time, other bearings need to be configured to offset their additional axial forces. When installed in pairs,Angular Contact Ball Bearings their additional axial forces offset each other, and they can bear the axial load of two forces upward, and have strong axial limit capacity in two directions,
Generally, two sets of bearings are installed in pairs, with their outer ring wide end face opposite (back-to-back) or narrow end face opposite (face-to-face), in which the rigidity of the back-to-back installation bearing system. In order to facilitate installation in pairs or groups, some bearing factories supply bearings in pairs, three sets in groups and four sets in groups.
In this way, the processing consistency of the supplied bearings in the same batch is good, the load is borne Angular Contact Ball Bearings more evenly during use, and the additional axial forces offset each other more thoroughly.
This type of bearing can be divided into two types: separated type and non separable type. The separated type bearing is used when the installation conditions are limited and the outer ring or inner ring is required to be removed Angular Contact Ball Bearings from the whole set of bearings for separate installation.
Because the separated type angular contact ball bearing is widely used in magneto, Angular Contact Ball Bearings it is also called magneto bearing. In this type of bearing, the locking port is on the inner ring, which can be adapted to higher speed.