We can provide samples for free

Send your needs: market@bearingsupplier.cn

Basic Principles For Cleaning And Maintenance Of Thrust Angular Contact Ball Bearings
Basic Principles For Cleaning And Maintenance Of Thrust Angular Contact Ball Bearings
How To Solve The Noise Of Fag Bearing And The Problems Needing Attention In Use
How To Solve The Noise Of Fag Bearing And The Problems Needing Attention In Use

Inspection Method Of Fag Bearing Lubricant

Inspection Method 

Rub with a little lubricant between your fingers. If there are pollutants, you can feel them; Or coat the Inspection Method back of the hand with lubricant, and then conduct light sealing inspection.

After draining the old oil, if possible, the fag bearing lubricated with oil should be filled with fresh oil and let the machine rotate at low speed for a few minutes. Make the oil collect Inspection Method residual pollutants as much as possible, and then drain the oil. Note: the engine oil is filtered before use.

Inspection Method Of Fag Bearing Lubricant

When changing the grease of fag bearing lubricated with grease, the Joe remover used shall avoid cotton from contacting any part of fag bearing. Because these residual fibers may wedge Inspection Method between rolling parts and cause damage, especially in the application of small bearings.

When inspecting fag bearings, never expose the bearings to pollutants or moisture. If the work is interrupted, cover the machine with oil paper, plastic sheet or similar materials.

How to solve the noise of fag bearing and the problems needing attention in use

Repair Method Of Lubricating Ntn Bearing

(1) Scar sound and its control method

If there is crack, indentation or corrosion on the rolling surface of rolling bearing, periodic vibration and noise like riveting rivet will Inspection Method occur. Its cycle can be fixed, but most of it has an inevitable corresponding relationship with the speed.

The scars will continue to occur on the channel, and the scars will appear on the steel ball from time to time, and this noise will change with the device and smooth premise.

The control methods of this kind of noise include: do not knock the bearing when installing the device, and avoid the oblique installation of the bearing when assembling Inspection Method the fag bearing with the shaft and then installing it into the bearing seat;

Avoid bearing corrosion during storage and impact vibration during transportation; Use smooth grease with high viscosity.

(2) Dust sound and its control measures

There are dust and other foreign matters in the rolling bearing, which will produce aperiodic vibration and so-called dust Inspection Method sound. The magnitude of vibration and noise is uncertain, and there is or no.

The control methods of dust noise include: improving the cleaning methods of bearings, and strictly clearing the bearings, shafts, seat holes and matching parts before the device; Remove foreign matters in the smoothing agent; Improve the sealing of bearings; Prevent the use of plastic holders with impure data or embedded foreign matters.

(3) Noise caused by lubricating elements and Its Countermeasures

Wrong selection of lubricant, lack of lubricant or aging hardening Inspection Method can lead to vibration and noise of fag bearing, and this noise has no inevitable rules.

For this situation, as long as the appropriate smoothing agent is selected, the smoothing dose is adjusted, the service life of the Inspection Method smoothing agent is extended, and the replacement cycle is reasonably determined.

Precautions for use:

Rolling bearing is a precision component, and its use must be carried out with corresponding caution. No matter how high-performance bearings are used, if they are not used properly, the expected high performance will not be obtained. Precautions for the use of bearings are as follows.

(1) Keep the bearing and its surroundings clean.

Even small dust that cannot be seen by the eyes will have a bad impact on fag bearings. Therefore, keep the surrounding clean so that the dust will not invade the bearing.

(2) Use with care.

Strong impact on the bearing during use will produce scars and indentation, which will become the cause of the accident. In serious cases, it will crack and fracture, so we must pay attention to it.

(3) Use proper operation tools.

Appropriate tools must be avoided to replace existing tools.

(4) Pay attention to the corrosion of bearings.

Sweat on your hands can be a cause of rust when operating fag bearings. Pay attention to operate with clean hands and try to wear gloves.

Chat with us
Chat with us
Questions, doubts, issues? We're here to help you!
None of our operators are available at the moment. Please, try again later.
Our operators are busy. Please try again later
Have you got question? Write to us!
This chat session has ended
Was this conversation useful? Vote this chat session.
Good Bad