How To Maintain Fag Bearings
How To Maintain Fag Bearings
How To Maintain Skf Bearing Correctly
How To Maintain Skf Bearing Correctly

Inspection Of Deterioration Method Of Nsk Bearing Grease

Inspection Of Deterioration 

NSK Bearings will encounter various problems during use. Inspection Of Today, let’s learn how to check the deterioration of NSK bearing grease.

In the process of using NSK Inspection Of Bearings, grease is very critical. If deteriorated grease is used, it will not only fail to play its due role, but also damage NSK Bearings.

① Oil flow observation method

Take two measuring cups, one Inspection Of containing the lubricating oil to be checked and the other empty on the table. Lift the measuring cup filled with lubricating oil 30-40 cm away from the table and tilt it, let the lubricating oil flow slowly into the empty cup, and observe its flow.

The lubricating oil with good quality should flow slender, Inspection Of uniform and continuous. If the oil flow is fast and slow, sometimes large pieces flow down, The lubricating oil has deteriorated.

Inspection Of Deterioration Method Of Nsk Bearing Grease

② Hand twisting

Twist the lubricating oil between the thumb and index finger and grind it repeatedly. The better Inspection Of lubricating oil hand feels lubricity, less wear debris and no friction.

If it feels a large friction feeling such as sand particles between the fingers, it indicates that there are many impurities in the Inspection Of lubricating oil and it can not be used again. It should be replaced with a new lubricating oil.

③ Illumination method

On sunny days, lift up the lubricating oil with a screwdriver at an angle of 45 degrees to the horizontal plane. Observe the condition of oil drops according to the sunlight. In the light, it can be clearly seen that there is no wear debris in the lubricating oil. It can continue to function. If there are too many wear debris, replace the lubricating oil.

④ Oil drop trace method

Take a clean white filter paper and drop several drops of oil on the Inspection Of filter paper. After the lubricating oil leaks,

if there is black powder on the surface and there is a sense of astringency by hand, it indicates that there are many impurities in the lubricating oil. Good Inspection Of lubricating oil has no powder, and it is dry and smooth by hand and shows yellow traces.

How to maintain SKF Bearing correctly

Failure Classification Of Imported Bearings

1. Cleaning

When the SKF Bearing is removed for inspection, the appearance record shall be made by photography and other methods. In addition, confirm the amount of remaining lubricant and sample the lubricant before cleaning the SKF Bearing.

a. SKF Bearing cleaning is divided into rough cleaning and fine cleaning, and a metal grid can be placed at the bottom of the container.

b. During rough cleaning, use a brush to remove grease or adhesion in the oil. At this time, if the SKF Bearing is rotated in oil, pay attention to the damage to the rolling surface due to foreign matters.

c. During fine cleaning, rotate SKF Bearing slowly in oil and carry out it carefully.

The commonly used cleaning agent is neutral water-free diesel oil or kerosene, and sometimes warm lye is used as needed. No matter what kind of cleaning agent you use, always filter it and keep it clean. After cleaning, coat SKF Bearing with antirust oil or grease immediately.

2. Inspection and judgment

In order to judge whether the removed SKF Bearing can be reused, its dimensional accuracy, rotation accuracy, internal clearance, mating surface, raceway surface, cage and sealing ring should be emphatically checked.

The inspection results can be judged by those who are used to SKF bearings or proficient in SKF bearings.

The judgment criteria vary according to mechanical properties, importance and inspection cycle. In case of the following damage, SKF Bearing shall not be reused and must be replaced.

1) Fracture and defect of SKF Bearing parts.

2) Stripping of the rolling surface of the raceway surface.

Chat with us
Chat with us
Questions, doubts, issues? We're here to help you!
None of our operators are available at the moment. Please, try again later.
Our operators are busy. Please try again later
Have you got question? Write to us!
This chat session has ended
Was this conversation useful? Vote this chat session.
Good Bad