How To Judge The Service Life Of Koyo Imported Bearing From Its Running Sound
How To Judge The Service Life Of Koyo Imported Bearing From Its Running Sound
2022年2月11日
How To Check The Operation Of Ina Imported Bearing
How To Check The Operation Of Ina Imported Bearing
2022年2月11日

Introduction To Methods And Methods Of Regular Lubrication And Maintenance Of Skf Bearings

Introduction To Methods

SKF Bearing Lubrication is implemented during the planned equipment shutdown and To Methods supplemented regularly. At the same time, the old grease is removed or squeezed out through the oil drain air.

Wipe the grease nipple clean before adding fresh grease. If To Methods there is no grease nozzle in the bearing box of SKF Bearing, open the bearing box cover or end cover to take out the old grease. After cleaning, add fresh grease of the same model.

In order to ensure the normal operation of SKF Bearing, we need to regularly check the oil level and oil quality of lubricating oil. To Methods Generally, the normal oil level should be within 1 / 3-2 / 3 of the equipment oil level window or mark.

The oil replenishment mode is the oil cup, and the displayed oil level only represents the oil replenishment capacity, while the oil level of the bearing box meets the operation requirements. If the oil level in the oil cup is lower than 1 / 4 of its total volume, oil To Methods replenishment can be considered.

The method of inspection and oil replenishment is to take a small amount of lubricating oil as a sample and compare it with fresh lubricating oil. Competent units can consider oil quality test to ensure that the oil quality is qualified. If the sample looks like a cloud, it may be the result of mixing with water,

which is often called oil emulsification. At this time, the lubricating oil should be replaced. If the sample becomes darker or thicker, it may indicate that the lubricating oil has begun to To Methods carbonize, and the old lubricating oil should be completely replaced. If possible, flush the oil circuit with fresh lubricating oil.

When replacing the lubricating oil, ensure that the new and old To Methods models of the replaced lubricating oil are the same, and supplement it to meet the required oil level.

Introduction To Methods And Methods Of Regular Lubrication And Maintenance Of Skf BearingsIntroduction To Methods And Methods Of Regular Lubrication And Maintenance Of Skf Bearings

Use the oil bath lubrication system. If the oil temperature is below 60 ℃ (140 ° f) and the lubricating oil is not polluted,

replace the lubricating oil once a year. If the oil temperature is 60-100 ℃ (140-210 ° f), the lubricating oil needs to be changed four times a year. If the oil temperature is 100-120 ℃ (210-250 ° f), the lubricating oil needs to be changed once a month. If the oil temperature is above 120 ℃ (250 ° f), the lubricating oil needs to be changed once a week.

Correct installation and maintenance is an important factor for the normal operation of the bearing. At the same time, attention must be paid to To Methods maintaining the cleanliness of the bearing.

The bearing must be protected from contamination by pollutants and moisture, and must be correctly installed and lubricated. In addition, the design of bearing arrangement, the condition of oil seal, the form and replacement cycle of lubricant and special maintenance also play an important role, which must be paid attention to.

There may be many factors To Methods affecting the service life of Koyo imported bearings. The factors that may lead to and the internal friction sound have been further explained. The main factors used for adjustment are installation, use and maintenance, maintenance and repair, which meet the technical requirements.

According to the technical requirements for the installation, use, maintenance and maintenance of Koyo imported bearings, the contact load, speed and lubrication status of the bearings are monitored and inspected. The direct cause of abnormality is found and adjusted back to normal.

Installation conditions, one of the factors used for bearings is the load-bearing force that often causes the change of state between various parts of the incorrect installation package, the primary factor of abnormal state of bearing working temperature, vibration, noise, gradual progress, and the quality of raw materials has been improved.

The proportion of raw material quality factor in bearing fault analysis has decreased significantly, but it is still one of the main factors of bearing failure.