by 
| Bearing Type | Open | |
| Bore Dia (d) | 40.000 | mm |
| Outer Dia (D) | 120.000 | mm |
| Radius (min) (rs) | 2.10 | mm |
| Dynamic Load Rating (Cr) | 81,900 | N |
| Static Load Rating (Cor) | 52,200 | N |
| Max Speed (Grease) | 5,300 | rpm |
| Max Speed (Oil) | 6,300 | rpm |
| Ball Qty | 8 | |
| Ball Dia (Dw) | 20.000 | mm |
| Width (B) | 72.000 | mm |
| Max. Shaft Shoulder Dia. Inner (Li) | 79 | mm |
| Min. Housing Shoulder Dia., Outer (Lo) | 119 | mm |
| Weight (g) | 1,699.00 | grams |
| Precision | A1 | |
| Standard Clearance | C0 | |
| Material | 52100 Chrome steel (or equivalent) |
SKF 6407 Deep Groove Ball Bearing
Timken 6407 Deep Groove Ball Bearing
NSK 6407 Deep Groove Ball Bearing
NTN 6407 Deep Groove Ball Bearing
Koyo 6407 Deep Groove Ball Bearing
NACHI 6407 Deep Groove Ball Bearing
Deep groove ball bearings mainly bear radial load, and can also bear radial load and axial load at the same time. When it only bears radial load, the contact angle is zero.
When the deep groove ball bearing has large radial clearance, it has the performance of angular contact bearing and can bear large axial load.
The friction coefficient of deep groove ball bearing is very small and the limit speed is also very high. Especially under the high-speed operation condition with large axial load, deep groove ball bearing has more advantages than thrust ball bearing
Shipping port: Qingdao/Tianjin
Supply Ability: 100,000 pieces per month
Package：
Due to their internal design, ball bearings cannot usually be disassembled down to the component level; therefore, they cannot usually be refurbished.
Solid base shells are manufactured without cavities and fillers; they are stronger than hollow bases, and there are no traps for bacteria and fungi to grow. In the thermoplastic shell, the sturdy base will not break under steam or high-pressure washing. The hollow base saves material and weight to reduce costs. Some people use epoxy resin to backfill the hollow base to eliminate the trap of bacteria breeding, but this will not increase the strength, will cause the installation surface to be uneven, and water will seep between the shell and the filling material, causing cracking.
Use particularly thermally stable bearing rings, larger internal clearance (C4), specially selected lubricants that will not decompose at high temperatures, and zinc anodized flinger. There are two basic versions of our high temperature bearings. The suffix “C4HR5” represents the bearing that can withstand 400°F, and the suffix “C4HR23” represents the bearing that can withstand 450°F.
For critical applications such as pulp and paper processing, printing and packaging, material tearing can cause expensive downtime due to excessive torque and vibration.
The two biggest factors affecting the starting and running torque of the bearing are the seal design and lubricant selection. The shaft and bearing seat fit, component accuracy and surface finish, and retainer design also have some influence.
In higher speed applications, non-contact sealing devices are usually required to minimize operating torque and heat generation, so oil baffle rings and secondary sealing devices are usually required. Flowing oil lubrication systems are usually the best solution.
After proper installation, most seated bearings only need to be relubricated regularly with a small amount of grease and checked to ensure that they operate at low temperatures, quietness, and sufficient accuracy.
This depends on many factors, such as the application’s load conditions, operating speed, duty cycle, temperature, and operating environment. The technical information section of this website provides some basic information. Our engineers can help you determine more specific theoretical life calculations.
When noise and/or operating temperature increase or operating accuracy decreases, bearings should be replaced.
Lubricant of choice
Lubrication joint type or location
Sealing materials and design options
Dimensions, suitable for housing or insert
Fixing screw options
Paint the shell in any color
Too little or too much lubricant
Incorrect lubricant type
Poor bearing installation
Improper internal clearance
Excessive load and/or speed
Extreme temperature
Pollution
Movement between mounting surfaces
The noise emitted by the bearing may be caused by a combination of one or more factors, such as insufficient working clearance, excessive working clearance, changes in working clearance due to temperature, damage to the contact area, contamination, inappropriate lubricants or The raceway is damaged.
Lubricants have five basic functions for bearings:
Reduce friction
Reduce wear
Reduce temperature rise
Minimize corrosion
Seal contaminants
We do not recommend mixing grease. Mixing incompatible greases will cause the mixture to harden, preventing it from releasing any oil. Mixing incompatible greases can also soften the mixture, which releases all the oil. In either case, the mixture will not be able to properly lubricate the bearing. We strongly recommend using the same type of grease originally provided with the bearing.
