Improvement Measures to Prevent Damage of Plane Thrust Ball Bearing
Improvement Measures to Prevent Damage of Plane Thrust Ball Bearing
2022-03-27
How to Identify Refurbished Bearings
How to Identify Refurbished Bearings
2022-03-27

니들롤러베어링 클리어런스 변경 불량 유지 보수 기술

  • 일반적으로, the temperature of NTN bearing starts to rise slowly with the operation of the bearing and reaches a stable state after 1-2 시간. The normal temperature of rolling mill bearing varies with the heat capacity, 방열, 기계의 속도와 부하.
  • 윤활 및 설치 부품이 적절한 경우, 베어링 온도가 급격히 상승하고 비정상적인 고온이 발생합니다.. 이때, 작업을 중지하고 필요한 예방 조치를 취해야 합니다..
  • The thermal sensor can monitor the working temperature of the bearing at any time, and automatically alarm or stop when the temperature exceeds the specified value to prevent the occurrence of combustion shaft accident.Needle Roller 베어링 Clearance Change Failure Maintenance Technology
  • High temperature often indicates that NTN bearing is in abnormal condition. High temperature is also harmful to the lubricant of rolling mill bearings. 때때로 베어링 과열은 베어링의 윤활유로 인한 것일 수 있습니다.. If the temperature of the bearing exceeds 125 오랫동안 ℃, the service life of the bearing will be reduced.
  • The causes of high temperature bearings include insufficient or excessive lubrication and lubricant. 불순물이 들어있다, 과도한 부하, 베어링 링 손상, 불충분한 정리, 오일 씰로 인한 높은 마찰, etc.Needle Roller Bearing Clearance Change Failure Maintenance Technology
  • 그러므로, it is necessary to continuously monitor NTN bearing temperature, whether it is measuring the rolling mill bearing itself or other important parts. 작동 조건이 변경되지 않은 경우, any temperature change can indicate that a fault has occurred.Needle Roller Bearing Clearance Change Failure Maintenance Technology
  • In fact, the bearing faults we analyzed before are not so possible. High temperature is also harmful to the lubricant in the bearing. Sometimes the overheating of the bearing can be attributed to the lubricant of NTN bearing. If the bearing operates for a long time at a temperature of more than 125 ℃, the service life of high-temperature bearing will be reduced.
  • The reasons for high-temperature bearing include insufficient or excessive lubrication, magazine contained in the lubricant, 과도한 부하, damage of rolling mill bearing and insufficient clearance, And high temperature friction caused by oil seal, 등. Well, let’s summarize these.
Technical requirements for Timken non-standard bearing
  • If you are incomplete, we can only say so much about the failure of NTN bearing.Needle Roller Bearing Clearance Change Failure Maintenance Technology
  • Bearing maintenance is a necessary condition for the operation of ina combined needle roller bearing. The common maintenance is for the lubrication of bearing. After reading how to select the lubrication mode of bearing and understanding the lubrication mode of bearing, it is also necessary to understand the maintenance of bearing system. Let’s see how to carry out bearing lubrication and maintenance.

니들롤러베어링 클리어런스 변경 불량 유지 보수 기술

1、 The use and installation shall be careful, and strong stamping is not allowed. The solution to the bad phenomenon of ina combined needle roller bearing is not allowed to directly knock the bearing with a hammer, and the pressure is not allowed to be transmitted through the rolling body.Needle Roller Bearing Clearance Change Failure Maintenance Technology

2、 Use proper and accurate installation tools, try to use special tools, and try to avoid using cloth and short fiber.Needle Roller Bearing Clearance Change Failure Maintenance Technology

3、 Keep ina combined needle roller bearing and its surrounding environment as clean as possible. Sodium base grease is generally used for motor bearing. Even if the invisible smile dust enters the bearing, it will increase the wear, vibration and noise of the bearing.

니들롤러베어링 클리어런스 변경 불량 유지 보수 기술
  • To prevent the corrosion of ina combined needle roller bearing, when taking the bearing directly by hand, fully wash the sweat from your hands and apply high-quality mineral oil before operation. Pay special attention to rust prevention in rainy season and summer.
  •  Under some special operating conditions, ina combined needle roller bearing can obtain a longer life than the traditional calculation, especially under light load. Analysis on the mechanism and influencing factors of labyrinth seal of bearing box these special operating conditions are that when the rolling surface (track and rolling parts) of the bearing is effectively separated by a lubricating oil film and limits the possible surface damage caused by pollutants.
  • Lubricants are important not only for bearings, but also for all bearings. 하지만, please note that ina combined needle roller bearing should not add too much grease.
  • Then it’s time to change the lubricant of the bearing. After draining the old engine oil, if possible, the bearings lubricated with engine oil should be filled with fresh engine oil and let the machine rotate at low speed for a few minutes.
  • Make the oil collect residual pollutants as much as possible, and then drain the oil. When replacing the grease of the bearing lubricated with grease, the Joe remover used shall avoid the contact of cotton with any part of the bearing. Because these residual fibers may wedge between rolling parts and cause damage, especially in bearing applications.
Technical requirements for Timken non-standard bearing
우리와 채팅
우리와 채팅
질문, 의심, 문제? 우리는 당신을 돕기 위해 여기 있습니다!
연결 중...
현재 사용할 수 있는 운영자가 없습니다.. 제발, 나중에 다시 시도.
우리 교환원은 바쁘다. 나중에 다시 시도 해주십시오
:
:
:
:
질문있어?? 우리에게 쓰기!
:
:
이 채팅 세션이 종료되었습니다
이 대화가 유용했습니까?? 이 채팅 세션에 투표.
좋은 나쁜