Several Necessary Points For Attention When Using Fag Non-Standard Bearings

Usually, when we use fag non-standard bearings, we don’t pay attention to the key points, so it’s easy for our bearings to get the running state and long service life. Today we want to introduce how to master these key points and how to detect the clearance of fag non-standard bearings. Let’s start to understand.

Use of FAG non-standard bearings

The reason why fag non-standard bearing can obtain a longer service life than traditional calculation, especially under light load. These special operating conditions are the surface damage that may be caused when the rolling surface (track and rolling parts) is effectively separated and limited by a lubricating oil film.
Even if invisible smile dust enters fag non-standard bearing, it will increase bearing wear, vibration and noise. Fully wash the sweat from your hands and apply high-quality mineral oil before operation. Pay special attention to rust prevention in rainy season and summer.
It is not allowed to punch with force, directly knock the bearing with a hammer, and transfer pressure through the rolling element.

The causes of Fag Non-Standard Bearings

Since water-soluble cutting fluid is used for oil-free bearings, users Fag Non-Standard Bearings must make more efforts in machine tool maintenance and treatment to control erosion and even basically eliminate erosion.
In order to prevent water from eroding the metal surface, the Fag Non-Standard Bearings machine tool should always be fully lubricated and the important parts of the machine tool should be coated with grease.
Oil – free bearing can have a long service life under accurate use If there is premature damage, it is likely to be caused by wrong type selection, improper use or poor lubrication.
Therefore, when installing IKO bearing, we need to record the type of machine, installation position, use premise and nearby cooperation. By studying and summarizing the types of bearing damage and the use environment when the problem occurs, so as to avoid similar situations from happening again.
Properly control the concentration of cutting fluid. When the machine tool stops working, wash the Fag Non-Standard Bearings surface of the machine tool with cutting fluid, and open the shield of the machine tool to disperse the moist air in the working area of the machine tool.
In order to prevent the occurrence of electric corrosion, a layer of Fag Non-Standard Bearings waterproof lubricating grease shall be applied on the metal surface. Moreover, the machine tool should be strictly grounded, and it is not enough to only ground the electrical cabinet.
In order to avoid the breeding and reproduction of bacteria, the cutting fluid should be cleaned or replaced on schedule, the chips should be removed in time, and the cutting concentrate should be diluted with soft water (pure water with low mineral content).
In addition to excellent quality, oil- Fag Non-Standard Bearingsfree bearing is also a very precise part. It is both a high-performance bearing. If it is not used properly in the process of use, it will not only fail to achieve the expected functional effect, but also easily damage IKO bearing. Everyone must have paid attention to lubrication.
When using and installing, it is necessary to be careful. Strong stamping is not allowed. It is not allowed to knock the bearing vertically. It is not allowed to Fag Non-Standard Bearings transfer pressure through the moving bullet body.
Use proper and correct installation tools, try to use special tools, and try to avoid using cloth, short fiber and other things.Try to keep the bearing and its surrounding environment clean. Even if the invisible smile dust enters the bearing, it will increase the wear, vibration and noise of IKO bearing.
To prevent the corrosion of IKO bearing, when taking the bearing directly by hand, fully wash the liquid on your hand and apply high-quality mineral oil before operation. Pay special attention to rust prevention in rainy season and summer.Under a special operating condition, oil-free bearing can obtain a longer service life than traditional calculation, especially under light load.
These special control premise is that when the moving surface (track and moving parts) is effectively separated by a lubricating oil film and limits the possible surface Fag Non-Standard Bearings damage caused by pollutants. In fact, under the ideal premise, the so-called permanent IKO bearing life is possible.

We can provide samples for free

General Bearings

Specialized Bearings

OEM Bearings

Strategy and Planning

Strategy and Planning

Vibration Maintenance And Detection Method For Iko Tapered Roller Bearing

Introduction To The Causes Of Iko Bearing Corrosion And Its Prevention Methods

Several Necessary Points For Attention When Using Fag Non-Standard Bearings

Use of FAG non-standard bearings

The causes of Fag Non-Standard Bearings

CONTACT US

Guarantees & Return policy

FOLLOW US:

Types of Bearings

Get Your Free Quote